Plaster removing tools

Before you start the plaster removal process, you need to cover the floor. Apart from that, you also need to wear a mask and gloves for safety. You cannot remove old plaster from the walls with your bare hands. You need to use plaster removal tools to remove it. Here is a list of all the tools you will need. Plaster is the most common type of wall covering for concrete walls.

It makes the concrete walls smooth and durable. When you apply the wet plaster on concrete walls, it dries and becomes very strong. So in order to remove the old plaster, you need to scrape a lot and dissolve the leftover plaster with acid. If you want to remove plaster from concrete walls, follow this step-by-step process.

Removing plaster can lead to lots of dust and debris. So you need to prepare the area first. You need to remove all the furniture from the room and cover the floor with plastic wrap or newspaper. Apart from that, you need to use gloves and a mask for safety. After preparing the area, you need to start removing the plaster. To start the process, you need to use a hammer and break the plaster on the walls.

When cracks will appear in the wall, use a paint scraper to scrape away all the cracked and removable plaster. If you own hammer drill and chisel bit for it, you can use those as well. It will make the job easier. In order to remove the leftover plaster from the walls, you need to dampen a cloth with muriatic acid and place it on the stuck plaster. After that, you need to put a plastic wrap to cover the cloth on the wall.

Stick it with tape and let it rest for a day. The plaster will soak the acid and become loose or get dissolved. After a day, you need to remove the plastic wrap from the wall along with the cloth. By now, most of the plaster might have dissolved.

You need to use a paint scraper to loosen the remove the plaster from the walls. Plaster is also applied on drywall to make the walls strong and smoother. However, removing plaster from drywall can be pretty time-consuming. Most of the time, while removing the plaster, you have to tear the drywall paper. If you want to remove old plaster from drywall, follow these steps. The first thing you need to do is scraping off the old removable plaster from the drywall. You need to use a drywall knife to do it.

You need to remove the leftover plaster from the drywall using a utility knife. All you need to do is insert the pointy side into the edge of the plaster and remove it. All the scraping might damage the drywall paper, so you need to cut the hanging pieces with a utility knife. After that, you need to fix the damaged drywall paper by applying a drywall primer and joint compound.

It is the most common type of wall in old homes. If you have brick walls in your house and want to restore them, you need to remove the plaster first. With time, brick walls become weak because of old plaster. You need to remove the old plaster and apply a new coat to make it strong again. Follow these steps to remove plaster from brick walls.

The first thing you need to do is chip off all the old and weak plaster from the wall. You can use a hammer to crack the plaster and a chisel to chip it off. In order to remove the small stuck pieces of plaster, you need to use a hydrochloric solution.

The most difficult aspect of removing plaster is avoiding damage to adjacent areas. Before you begin removing plaster, turn off any nearby circuits at the electrical service panel. Remove all receptacle and switch coverplates. Wear a dust mask rated for fine dust. Expect to spend about 1 to 2 hours per 8-foot section of wall.

Before you begin, isolate the work site to contain the mess and determine what utilities may be contained within the wall. Plaster is a tough wall surface, but too much pounding and vibration can jar it loose in places you don't want to remove. To avoid problems, attach 1x2s in the corners of walls and the ceiling adjacent to the wall you are removing.

If you remove only part of a wall, stop at a stud. You can't cut through lath in the middle of a bay without destroying the plaster. Attach a reinforcing 1x2 along the stud. Knock the plaster off the wall with a hammer. It is easier to shovel up the loose debris before the lath is mixed in.

If lath strips continue past the end stud, cut them flush to the side of the end stud with a handsaw or reciprocating saw. As you remove the lath with a flat pry bar, some of the lath nails will stay in the studs; others will come away with the lath. Either way, it's best to remove the nails as you go and pile the lath neatly for disposal.